|
| MBD-X8QBE-F
-O |
- X8QBE-F
(Standard Retail Pack)
|
| MBD-X8QBE-F
-B |
|
| |
| Form Factor |
|
| Dimensions |
- 16.4" x 16.8" (41.66cm x 42.65cm)
|
| |
| CPU |
- Quad 1567-pin LGA Sockets
- Supports up to four Intel® Xeon® 64-bit processor(s) of the same type below:
- Intel® Xeon® processors 7500 series (8-core, codename Nehalem-EX) and new generation Intel® Xeon® processors E7-4800 family (10-core, codename Westmere-EX)
|
| QPI |
|
| |
| Memory Capacity |
- 32x 240-pin DIMM sockets
- Supports up to 1024 GB 1066 / 978 / 800MHz DDR3 ECC Registered memory
- Memory Mirroring supported
|
| Memory Type |
- 1333* / 1066 / 978 / 800MHz ECC Registered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
- 1GB, 2GB, 4GB
, 8GB
, 32GB**
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
| |
| Chipset |
- Intel® 7500 (Boxboro-EX) chipset
- ICH10R
|
| SATA |
- Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Winbond® WPCM450 BMC
|
| Network Controllers |
- Intel® 82576 Dual-Port Gigabit Ethernet Controllers
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics |
|
| Super I/O |
|
| |
| Serial ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
| LAN |
|
| USB |
- 2x USB rear ports
- 2x USB internal headers (3 ports)
- Total 5 USB 2.0 Compliant
|
| VGA |
|
| Serial Port / Header |
- 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
|
|
|
| 1U Chassis |
- CSE-818A-1400LPB
(rev. K required, Air Shroud MCP-310-81804-0B)
|
| 2U Chassis |
- CSE-828TQ-R1400LPB
(rev. K required, Air Shroud MCP-310-82805-0B)
|
| Tower / 4U Rackmount |
- CSE-418E16-R1K62B
- CSE-848A-R1K62B
- CSE-848E16-R1K62B
(for SC748, rev. K required, Air Shroud MCP-310-74805-0B)
(for SC848 & 418, rev. K required, Air Shroud MCP-310-84803-0B)
|
| Important Chassis Notes |
- To support the new generation Intel® Xeon® processor-based motherboards, a Revision K chassis is recommended for most models. Please talk to your sales representative or follow the link for details.
|
| |
| PCI-Express |
- 2 (x16) PCI-E 2.0 or 1 (x16) PCI-E 2.0 + 2 (x8) PCI-E 2.0 or 4 (x8) PCI-E 2.0 slots
|
| |
| BIOS Type |
- 32Mb SPI Flash EEPROM with AMI® BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| |
| Software |
- IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
|
| Power Configurations |
- ACPI / ACPM Power Management
|
| |
| Voltage |
- Monitors for CPU Cores, +1.2V, 1.5V, +3.3V, +12V, (+3V, 1.0V, 1.2V, 1.8V, 1.1V) Standby, VBAT, Memory, Chipset Voltages.
- 4-Phase-switching voltage regulator with auto-sense from 0.6V-1.35V
|
| FAN |
- Total of 10 fan headers supporting up to 10 fans
- Ten 4-pin fan headers
- 10x fans with tachometer status monitoring
- Support 4-pin fans (w/o speed control)
- Low noise fan speed control
|
| Temperature |
- Monitoring for CPU and chassis environment
- Thermal Control for 8x fan connectors
- PECI
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
|
| |
|
RoHS
|
- RoHS Compliant 6/6, Pb Free
|
| Environmental Spec. |
- Operating Temperature: 10° to 35° C (50° to 95°F)
- Non-operating Temperature: -40° to 70° C (-40° to 158° F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|
