| |
| Form Factor |
|
| Dimensions |
- 12.8" x 16.5" (32.5cm x 41.9cm)
|
| |
| CPU |
- Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Intel®
Xeon®Processor 5600 Series (Westmere)
- Intel®
Xeon®Processor 5500 Series (Nehalem-EP)
|
| QPI |
|
| |
| Memory Capacity |
- 18x 240-pin DIMM sockets
- Supports up to 384GB 1066MHz ECC LRDIMM ECC
- Supports up to 192GB 1333 / 1066 / 800MHz DDR3 ECC Registered DIMM
- Supports up to 48GB 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered DIMM
- Memory Mirroring supported
|
| Memory Type |
- 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated LRDIMMs
|
| DIMM Sizes |
- 1GB, 2GB, 4GB, 8GB, 16GB, 32GB
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
| |
| Chipset |
- Intel® 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
|
| SAS |
- LSI 6Gbps SAS 2108 w/ Hardware RAID support
- RAID 0, 1, 5, 6, 10, 50, 60 support
- BBU (battery backup) extension kit (optional)
- Onboard 512MB cache
|
| SATA |
- Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Winbond® WPCM450 BMC
|
| Network Controllers |
- Intel® 82576 Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics |
|
| Super I/O |
|
| |
| SAS |
- 8x 6Gbps SAS / SATA ports with 2 I-PASS connectors
|
| Serial ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
| LAN |
- 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB |
- 2x USB rear ports
- 1x USB on-board
- 3x USB internal headers
- Total 6 USB 2.0 Compliant
|
| VGA |
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Port / Header |
- 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
|
|
|
| 1U Chassis |
- CSE-119TQ-R700UB
- CSE-819TQ-R700UB
|
| 2U Chassis |
- CSE-219A-R920UB
- CSE-829TQ-R920UB
|
| Important Chassis Notes |
- To support the new generation Intel® Xeon® processor-based motherboards, a Revision K chassis is recommended for most models. Please talk to your sales representative or follow the link for details.
|
| |
| PCI-Express / PCI-X / UIO |
Left Side
- 1 (x16) PCI-E 2.0 by riser card
Right Side
- 1 (x4) PCI-E 2.0 by riser card
- For 2U configuration, Please go to UIO Riser Cards page
|
| |
| BIOS Type |
- 32Mb SPI Flash EEPROM with AMI® BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| |
| Software |
- IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
|
| Power Configurations |
- ACPI / ACPM Power Management
|
| |
| Voltage |
- Monitors for CPU Cores, +1.8V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory, Chipset Voltages.
- 6-Phase-switching voltage regulator
|
| FAN |
- Total of eight fan headers supporting up to 8 fans
- Eight 4-pin fan headers
- 8x fans with tachometer status monitoring
- Support 3-pin fans (w/o speed control)
- Low noise fan speed control (4-pin fan only)
|
| Temperature |
- Monitoring for CPU and chassis environment
- Thermal Control for 8x fan connectors
- PECI
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
|
| |
|
RoHS
|
- RoHS Compliant 6/6, Pb Free
|
| Environmental Spec. |
- Operating Temperature: 10° to 35° C (50° to 95°F)
- Non-operating Temperature: -40° to 70° C (-40° to 158° F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
| |
• Please see our OS Compatibility Chart |
|
