|
| MBD-X9DAX-7TF-O |
- X9DAX-7TF (Standard Retail Pack)
|
| MBD-X9DAX-7TF
-B |
|
| |
|
| Form Factor |
|
| Dimensions |
- 13.68" x 13" (34.74cm x 33cm)
|
| |
| CPU |
- Intel® Xeon® processor E5-2600 (up to 150W TDP **)
- Dual Socket R (LGA 2011)
|
| Cache |
|
| System Bus |
|
|
** Motherboard supports this maximum TDP. Please verify your system can thermally support |
| |
| Memory Capacity |
- 16x 240-pin DDR3 DIMM sockets
- Supports up to 512 GB DDR3 ECC Registered memory (RDIMM)
- Supports up to 128 GB DDR3 ECC/non-ECC Un-Buffered memory (UDIMM)
|
| Memory Type |
- 1600/1333/1066/800MHz ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Support ECC and non-ECC UDIMMs
|
| DIMM Sizes |
- 32GB, 16GB, 8GB, 4GB, 2GB, 1GB
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| |
| Chipset |
|
| SATA |
- SATA 2.0 3Gbps with RAID 0, 1, 5, 10
- SATA 3.0 6Gbps with RAID 0, 1
|
| SAS |
- SAS2 from LSI 2208 (1GB cache)
- HW RAID 0, 1, 5, 6, 10, 50, 60 support
- Supports up to 16 drives
(Both CPUs need to be installed for SAS controller to be enabled)
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
|
| Network Controllers |
- Intel® X540 Dual Port 10GBase-T
- Virtual Machine Device Queues reduce I/O overhead
- Supports 10GBase-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Video |
|
| Audio |
- RealTek ALC889 7.1 High Definition Audio with S/PDIF header
|
| |
| SATA |
- 2 SATA 3.0 ports (6Gbps)
- 8 SATA 2.0 ports (3Gbps)
|
| SAS |
|
| LAN |
- 2 RJ45 10GbE LAN ports
- 1 RJ45 Dedicated IPMI LAN port
|
| USB |
- 4 USB 3.0 ports (2 rear + 2 via header)
- 7 USB 2.0 ports total
(4 rear + 2 via header + 1 Type A)
|
| Audio |
- Line-in / Line-out / Microphone Ports
|
| Serial Port / Header |
|
| IEEE 1394a |
|
| DOM |
- 1 DOM (Disk on Module) power connector
|
| TPM |
|
|
|
|
| 2U Chassis |
|
| Tower / 4U Rackmount |
|
| Important Chassis Notes |
- To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis is recommended. Please talk to your sales representative for details.
|
| |
|
| PCI-Express |
- 2x PCI-E 3.0 x16
- 3x PCI-E 3.0 x8
- 1x UIO PCI-E 3.0 x8 (for SMC UIO HBA) or 1x PCI-E 2.0 x4 (in x8)
(Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.)
|
| |
| BIOS Type |
- 128Mb SPI Flash EEPROM with AMI BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI
|
| |
| Software |
- SuperDoctor® III
- Watch Dog
- NMI
- IPMI 1.5 / 2.0
|
| Power Configurations |
- ACPI / APM Power Management
- Power-on mode for AC power recovery
|
| |
| Voltage |
- Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory Voltages.
- 6+1 Phase-switching voltage regulator
|
| FAN |
- 8x 4-pin fan headers (up to 8 fans)
- 8x fans with tachometer monitoring
- Status monitor for speed control
- Pulse Width Modulated (PWM) fan connectors
|
| Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED |
- CPU / System Overheat LED
- Suspend static indicator LED
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
- RoHS, Halogen Free
|
| |
|
| Operating Temperature Range |
- 10°C - 35°C (50°F - 95°F)
|
| Non-Operating Temperature Range |
- -40°C - 70°C (-40°F - 158°F)
|
| Operating Relative Humidity Range |
- 8% - 90% (non-condensing)
|
| Non-Operating Relative Humidity Range |
- 5% - 95% (non-condensing)
|
|
